Tempest Technology 16

Tempest Technology 16"Smoke Ejector, Explosion Proof

Tempest Technology 16 Tempest Technology
TheFireStore

Tempest Technology 16"Smoke Ejector, Explosion Proof

$1459.59
Product Code:
700-152

QUANTITY:
Select your options above to check stock status.
Product SKU:

 
Made In USA

Tempest's EBS-16 Explosion Proof Smoke Ejector, is a popular unit for all forms of confined space ventilation, one that's been around for decades.

It's light and small enough to ventilate tight areas but still built to Tempest's standard of long lasting durability and reliability. Plug it in and suck the smoke/fumes/particulates out from almost any location.

Single Speed AOC Motor
The EBS-16 comes with a Hazardous location (Explosion Proof, EP) motor which is intended for Class 1, Group C&D and Class 2 Group F&G environments.It is a single speed electric AOC motor with an output of 0.3 HP. This specific motor is matched perfectly with the fan blade's size and pitch to produce the most effective air movement possible. 

Hang/Suspend the EBS-16
One of the key advantages to the EBS-16's light weight and compact design is its ability to be quickly suspended in nearly any door or window way. Want to ventilate a difficult to access and crowded interior space through a window? No problem.

NOTE: For safety, it is encouraged to use the Door Bar Holder (300-141) and Hanging Bracket Set (300-142) to properly hang the Tempest EBS-16.

Lightweight
At 47 lbs, the Tempest EBS-16 is one of the more lightweight ventilation units available. Its reduced dimensions and frame design allow users to easily carry it to and from the work site.

Formed & Welded Roll-Cage Frame
Every bend and cross brace weld is structurally engineered to increase the blower frame’s strength to weight ratio by as much as 30%. Welds eliminate the need to continuously maintain/tighten nuts and bolts. Its roll cage design gives protection to all angles and sides of the shroud and motor.

Safety Grille
Front and rear safety grilles feature a continuous spun wire body with four tie point bars. Meets strict European CE Safety Standards.

AirFlex Composition Impeller
Paired specifically with its equipped 0.3 motor, the uniquely designed impeller "wings" deliver maximum air volume (cfm), velocity and pressure possible. The impeller blades are made from a high strength composite fiberglass reinforced polyamide. Composite blades require less torque from the engine to spin resulting in increased CFM. Composites also provide increased safety, as the blades are designed to disintegrate upon impact with any foreign object. Aluminum or other metal blades may chip or fragment when structural integrity is compromised, throwing potentially dangerous shrapnel in any direction.

Compact Size
Originally intended for confined space ventilation, the EBS-16 is small enough to hang, sit or fit in a wide array of tight spaces. Whether space is a factor for you for in storing or using ventilation, this box fan will suit you perfectly.

Negative Pressure Ventilator
Negative Pressure Ventilation (NPV), as opposed to Positive Pressure Ventilation (PPV), is the method of using a fan to suck out unwanted particulates rather than blowing them out. The Tempest EBS-16's size and design is most effective and efficient at NPV; although, PPV may still be utilized to some degree.

Technical Specifications:
Type Negative Pressure Ventilation Fan - Smoke Ejector
Drive/Motor Single Speed Electric AOC - 0.3 HP Motor
GFCI Compatible: Designed to Run on 15 AMP Circuit - Actual Draw Approx. 5.2 AMP
110V / 60Hz Standard
Blade 16" Diameter assembly made up of 6 AirFlex Fiberglass reinformed Polyamide Blades
Shroud Integral Component of Frame
Grille Continuous circular wound, Zinc-Plated Steel with 4 tie points for additional safety
Meets UL & European CE safety standards
Frame Formed and welded sheet metal construction with powder coat finish
Dimensions 18.75” w x 14.25” d x 19.50” h

Special discounts may apply for high volume sales. Contact our Bids & Quotes department for more information.

Do you have questions about this product?

Get answers from real customers and in-house experts with AnswerBox.

1 Question | 1 Answer
Displaying question 1
  • Q:

    fire extractor unit, is the hose made of fire prove materials?
    Asked on 7/24/2015 by Bostic

    1 answer

    • CUSTOMER CARE

      A:

      No it is not, it will melt when exposed to heat

      Answered on 7/24/2015 by Bg
Displaying question 1

Do you have a question about this product?